What is CLP for rust?
The Extreme CLP is a one-step cleaner, lubricant, and protectant designed to break down and remove carbon, lead, and powder fouling while also providing enhanced rust and corrosion protection.
Use the non-toxic, biodegradable gun cleaning gel with the instructions below to quickly remove rust from the surface of your guns without harming the bluing. Apply Blue Wonder™ Gun Cleaner to rusted areas and work in with “0000” steel wool or a brass brush until the rust is loosened.
The most commonly used rust removing chemical is phosphoric acid. The solution creates a chemical reaction when applied to rust converting it to a water-soluble compound that can be scrubbed away quickly and easily.
Much like brass cleaners, chemical rust removers can be found in any hardware store. But many household cleaning items—like baking soda, lemon juice, vinegar, and even soda—can do the trick.
Treating Gun Rust
The best-case scenario is a light surface rust that's just starting and sometimes won't even leave a mark after it's removed. This type of rust is called flash rust, and with a little elbow grease most firearms are no worse for the wear.
If you're looking for a gun oil that excels at cleaning, lubricating, and preventing rust, Hoppe's Elite Gun Oil is the best, especially if you are cleaning a gun that receives regular maintenance.
Description. RADCOLUBE CLP (GUN OIL) is for cleaning, lubricating and short-term preservation of small and large caliber military weapons, operating in the temperature range of -51 to + 71 Degrees C (-60 to +160 Degrees F).
While “CLP” lubes may prove to be adequate in clearing guns that have jammed – it's also true guns will tend to jam more often and fire fewer rounds if they are treated solely with “CLP” liquids in all maintenance events.
Description. Hoppe's No. 9 rust and lead remover cloth is a pre-treated, multi-purpose cloth. Removes rust and lead deposits without hard scrubbing.
A multi-purpose cleaning cloth for guns, fishing reels, and much more, Hoppe's® No. 9 Quick Clean Rust and Lead Remover removes rust and lead deposits without hard scrubbing.
Does rust ruin a gun?
Rust is much more than an eyesore. It creates a rough surface on the moving parts of your gun, and this leads to drag. Drag impedes the function of your gun, making it unreliable. Rust degrades the moving parts in a gun by increasing the amount of wear between contact points.
- Vinegar bath. Best used on items that are all steel or on tools with significant rust, a vinegar bath takes very little elbow grease to work away the rust once soaked. ...
- Potato and soap. ...
- Lemon and salt. ...
- Baking soda. ...
- Citric acid.
Most people know WD-40 Multi-Use Product as a lubricant, but it was originally used as an anti-corrosive by the aerospace industry to prevent spacecraft from rusting. WD-40 can help remove rust from metals like iron, chrome, and stainless steel without further damaging the surface of the metal or removing the paint.
It is very effective as a rust remover as the rust simply reacts with the vinegar and dissolves. If the item you are removing rust from is small enough to be submerged in a bath of white vinegar, simply leave it in there for a few hours and then wipe the paste off.
- Soak or spray the rust with vinegar or Coke.
- Leave the vinegar to soak for 3 days, or Coke for 24 hours.
- Scrub away the rust.
- Use baking soda and water for stubborn rust spots.
- For a faster solution for outdoor surfaces, try a specialist cleaner like Cif Outdoor Rust Spray.
Humidity is the biggest culprit, he said. While most people wipe down their guns if they've been hunting or shooting in the rain or snow, storing guns in humid places for weeks or months at a time often leads to rust. “Store them in a place where you can at least monitor the humidity,” Goette said.
Pistols, rifles and shotguns all rely on metal components in order to function correctly, and this means that they are susceptible to rust and corrosion. Without proper storage, the rusting process can set in quickly and compromise the safety and functionality of your weapon.
The Science Behind Rusting
The iron oxide typically has a reddish, flaky appearance that becomes progressively worse over time. If left unaddressed, the iron oxide will spread, thereby jeopardizing the physical integrity of the iron. Iron can rust from either exposure to air or exposure to moisture.
Strong acids will dissolve rust, but they will also dissolve paint, finishes, and sometimes even the metal itself. Hydrochloric acid (which is also called muriatic acid in its diluted form), as well as phosphoric acid and sulfuric acid may be used in rust removal formulas using strong acids.
Currently, when cleaning a weapon, warfighters use a conventional wet lubricant known as CLP (cleaner, lubricant, and preservative) that is continuously reapplied.
Does CLP clean and lubricate?
CLP® Cleaner, Lubricant & Preservative. Break Free CLP (MIL-SPEC 63460F Type-A) is more than just gun oil. Trusted by Agencies and Military around the world, it was the first to pass MIL-SPEC 63460. CLP cleans burnt powder residue and other fouling materials from the gun's bore, moving parts, and exterior.
WD-40 is a solvent and NOT a lubricant. Because it evaporates so quickly WD-40 does not function well as a lubricant in guns. Between the time you spray it on the chamber or slide and the time you load your rounds and start firing, it would almost certainly be evaporated, leaving your gun bone dry.
Break-Free CLP is the standard for gun oils and is one of the best 'do it all' oil's for your gun. You might be looking to setup your first cleaning kit, or maybe looking for a different option for gun oils, I believe that this oil should be in every gun owners kit.
The product is not classified as hazardous according to OSH$ GHS regulations within the United States. The product is classified and labelled according to the CLP regulation.
According to the US military and their testing, CLP works well enough to keep their weapons maintained and operating in the field across a number of different conditions.
Since WD-40 is primarily a solvent it seems to make sense that it would be ideal for cleaning guns. However, cleaning your guns with WD40 is NOT advisable. Solvents, such as WD40, don't remove any gunk or slime. Solvents dissolve gunk, which then moves the dissolved goo to another area of your gun that you cannot see.
Soak the rust well but don't apply too much vinegar as this can run onto areas that you don't want to have treated. Allow the vinegar an hour or two to do its magic. Once the vinegar has had time to loosen the rust, use the brush to scrub the affected area, followed by the steel wool.
Hoppe's No. 9 Synthetic Blend Lubricating Oil: Formulated with synthetic additives, this oil protects your modern firearms from corrosion and rust.
You simply spray it on the surface, wait around ten minutes, and scrub it off with something abrasive. Its lubricating qualities loosen the bonds between the rust and the metal surface it has adhered to.
To remove light rust, leave parts in the solution for 1-3 hours. To remove heavy rust, leave parts in the rust removal solution overnight.
Does oiling remove rust?
Tool owners should have on hand a multi-purpose oil designed to clean, lubricate, and protect. To remove light rust from tools simply apply oil to a rag and wipe the metal thoroughly. If the articulating parts are rusted, working oil into rusted joints multiple times is usually effective.
What Makes Coca-Cola Such an Effective Cleaner? Coca-Cola is carbonated, which allows it to dissolve with metal oxides and break up rust on a variety of metals and alloys. Phosphoric acid also gives it rust-busting power, while citric acid makes it an effective stain remover.
When lead and other metal buildup becomes an issue, mixing up a 50-50 concoction of both white vinegar and hydrogen peroxide will cut right through. Soaking overnight will cause the metal to flake off. Use this mix sparingly, though, as a little will go a long way.
Tools that are too large to fit in a container can be wrapped in a cloth soaked with vinegar and sprinkled with salt, then put in a plastic bag. The vinegar-and-salt mixture needs time to break down the rust. This can take anywhere from one to three days.